Side sewer permits in Shoreline: fees, timeline & requirements (2026)

Everything you need to know about pulling a side sewer permit in Shoreline, Washington — when one is required, what it costs, how long review takes, what documents are required, and which inspections you can expect. Cited to Shoreline Planning & Community Development.

Look up your Shoreline address

Free lookup, no account needed — your lot lines and the house, with a plan to draw the side sewer, cited to Shoreline's source.

Permit required?
Always
Permit fee
Where the City's wastewater utility serves the lot, Shoreline bills a single-family side sewer permit at $267 an hour: a new connection has a 3-hour minimum, a repair or replacement or capping-off a 2-hour minimum, and a single-family pump a 5-hour minimum.
Review timeline
Not published by the city

When does side sewer work need a permit in Shoreline?

The side-sewer permit comes from the utility that owns the sewer main (the city, a sewer or water district, or a regional utility), under that utility's own code. Which utility is a per-property fact: a lot can sit inside a city for permitting and outside its sewer district, so confirm the owner of the main before applying. The utility's code, not a statewide rule, decides which work needs the permit: a new connection does, and many utility codes also require it for any repair, however short, and for capping or disconnecting a side sewer, so check that code before digging. WAC 51-56, the state plumbing code, governs how the building sewer is laid.

From Shoreline's own code

“A. Requirements for the number of residential or commercial structures that may be allowed on a side sewer and the sizing of side sewer pipes are set forth in the EDM. B. Unless authorized by the city, existing private side sewers or public side sewer stubs may not be used for service to new single-family residential structures, commercial structures, or for any property that is being redeveloped. C.”
Source ↗verified 2026-05-17

Required submittals

  • Site plan with sewer line route
  • Depth + slope detail
  • Cleanout locations
  • Utility locate ticket

Inspection sequence

  1. Pre-cover (open trench)
  2. Air / water test
  3. Final

Contractor specialties needed

Side sewer contractor

Who can do this work in Shoreline?

Kolmo Construction is a licensed Washington general contractor — KOLMOL*753JS, active through April 10, 2027, bonded and insured — working throughout Shoreline and King County. Kolmo prepares the drawings and submittals, files the side sewer permit with Shoreline Planning & Community Development, carries the project through review and inspections, and performs the construction. Call (206) 410-5100 for a Shoreline side sewer quote.

Notes & caveats

Issuing body is the sanitary sewer utility, not the building department, and inspection is the utility's too. Some utilities additionally require the contractor to hold a side-sewer card or registration before they will issue; it is not universal, so check the serving utility's own rules rather than assuming either way.

How to apply yourself

  1. 1. Draw the side sewer. Run an address lookup for your side sewer work in Shoreline — we'll pull your lot lines and the house, and you can draw the side sewer's run to the street on a plan of the lot.
  2. 2. Assemble submittals: the 4 documents under Required submittals above.
  3. 3. Submit through the city portal: Shoreline Planning & Community Development ↗
  4. 4. Track review. Respond to reviewer comments promptly.
  5. 5. Pay issuance fees (the sewer utility that serves the lot sets them) and pick up the permit. Inspection card travels with the job.

Or have Kolmo do it

Kolmo prepares the drawings and submittals, files with Shoreline Planning & Community Development, handles reviewer comments, and builds the project.

(206) 410-5100

Licensed WA general contractor KOLMOL*753JS · bonded & insured

Side sewer permits in Shoreline — FAQ

When does side sewer work need a permit in Shoreline?

The side-sewer permit comes from the utility that owns the sewer main (the city, a sewer or water district, or a regional utility), under that utility's own code. Which utility is a per-property fact: a lot can sit inside a city for permitting and outside its sewer district, so confirm the owner of the main before applying. The utility's code, not a statewide rule, decides which work needs the permit: a new connection does, and many utility codes also require it for any repair, however short, and for capping or disconnecting a side sewer, so check that code before digging. WAC 51-56, the state plumbing code, governs how the building sewer is laid.

How much does a side sewer permit cost in Shoreline?

Where the City's wastewater utility serves the lot, Shoreline bills a single-family side sewer permit at $267 an hour: a new connection has a 3-hour minimum, a repair or replacement or capping-off a 2-hour minimum, and a single-family pump a 5-hour minimum. Apply electronically via eTRAKiT (https://www.shorelinewa.gov/government/departments/planning-community-development/permit-center-remote-services/register-for-a-professional-etrakit-account). King County's sewer service area map shows about 7% of Shoreline served by the Highlands Sewer District instead; there the side sewer permit and its fees come from the district, under its own rules and fee schedule, not from the City, so confirm the lot's utility before applying. District: Highlands Sewer District (https://www.thehighlandsseattle.org/, the address King County's map gives for it).